HCIP-Transmission V2.0 H31-341 Training Material

  Edina  08-16-2019

H31-341 HCIP-Transmission V2.0 Exam is new released, now it is the only exam for HCIP-Transmission Certification, previous exam H31-331 HCNP-Transmission was retired and no longer to take in Pearson VUE. Passquestion team offers the latest HCIP-Transmission V2.0 H31-341 Training Material to help you well practiced and ensure you pass your Huawei H31-341 Certification exam successfully.

The difference between HCIP-Transmission V2.0 and V1.0

In order to match the demand of the enterprise for the transmission network talents, the HCIP-Transmission V2.0 has been greatly adjusted compared to the previous version (V1.0). The original two certifications (HCNP-Transmission-MSTP, HCNP-Transmission-OTN) will be combined into one certification (HCIP-Transmission), covering both OTN and MSTP directions, focusing on the mainstream direction OTN technology, and adding the introduction of new technologies, such as MS-OTN/SOM/FD/400G/TSDN, and introducing the PCM technology which is unique to enterprise networks.

H31-341 HCIP-Transmission V2.0 Exam Content

The HCIP-Transmission V2.0 exam includes a range of knowledge of NG WDM and some technical topics of MSTP. NG WDM includes: NG WDM System Hardware, NG WDM Equipment Networking and Application, NG WDM Optical and Electrical Layer Grooming, NG WDM service configuration, NG WDM Equipment Commissioning, NG WDM Equipment Protection, NG WDM Alarm Signal Flow, NG WDM System Troubleshooting, SOM/FD System Introduction, MS-OTN Technology Introduction and New Transmission Technologies; MSTP includes: Clock Protection, ECC Maintenance and Pointer Adjustment, PCM technology, Board Replacement, Discrete Service Analysis and Handling, MSTP equipment troubleshooting, ASON Introduction and Ethernet Service Common Indicator Test.

Download H31-341 HCIP-Transmission V2.0 Free Demo:

1. Which of the following descriptions are correct about the ASON software structure? (Multiple Choice)
A. Intelligent optical network consists of three planes
B. The management plane mainly refers to upper management such as network management.
C. Intelligent software mainly apply for management plane
D. The transmission plane refers to the traditional transmission network.
Answer: ABD

2. The transmission plane mainly performs functions such as optical signal transmission, multiplexing, configuration protection switching and cross-connection. And to ensure the reliability of the transmitted optical signal. However, the exchange action of this layer is carried out under the influence of the management dry surface and the control plane.
A. TRUE
B. FALSE
Answer: A

3. Which of the following are limitations of the alarm and performance analysis methods? (Multiple Choice)
A. Field maintenance personnel cannot understand the current operation status of the equipment.
B. The network administrator cannot obtain the alarms, the alarm occurrence time, and the historical alarms of the device.
C. When some faults occur, there may be no obvious alarms or performance events reported, and sometimes no alarms or performance events are found.
D. In the case of complex networking, service, and fault information, a large number of alarms and performance events may occur along with the occurrence of faults. Due to too many reports and performance events, maintenance personnel are unable to analyze.
Answer: CD

4. Which of the following data is the data that needs to be collected and saved in the event of a failure? (Multiple Choice)
A. Equipment alarms and performance events
B. Running status data of the NE and the board
C. Operation log of the network management
D. Configuration data of NEs and boards
Answer: ABCD

5. When the signal of the standard Ethernet frame length of 64 Bytes is connected to the Ethernet board, if the QinQ function is enabled, how many bytes is the actual frame length of the signal inside the board?
A. 64
B. 84
C. 68
D. 80
Answer: C

Leave And reply:

  TOP 50 Exam Questions
Exam