Question No : 1
An administrator finds that home shares cannot be configured in a new Files 3.5 deployment .
Why is this happening?

• A.NFS default access is set to Read Only.
• B.Multi-protocolaccess is not configured.
• C.Access Based Enumeration is not enabled.
• D.The system is deployed as a single FSV

Show Answers

Answer:

Question No : 2
A consultant is using a customer’s switch for installation. Although the 10GbE ports for each of the hosts are connected to the switch, the nodes fail to be discovered.
What is causing the issue?

• A.IPv6 is not enabled on the switch.
• B.IPMI port is not plugged in.
• C.Foundation VM is running on a Windows host.
• D.10GbE ports are configured with the incorrect duplex setting.

Show Answers

Answer:

Question No : 3
The networking team makes changes to the Top of Rack switches to which the Nutanix cluster are attached. A few VMs are able to communicate with each other on the same node but are unable to connect to other parts of the network.
What is the likely cause of this issue?

• A.There is a VLAN misconfigurationon the VMs.
• B.The vNIC port is disconnected on the affected VMs.
• C.There is a VLAN misconfiguration on the switch.
• D.Jumbo Frame are misconfigured across ports.

Show Answers

Answer:

Question No : 4
An organizations Nutanix Cluster is based on VMware vSphere. The cluster is configured to download software updates automatically. The administration needs to verify and eventually upgrade VMware hypervisor via Prism Ul.
After logging in to Prism, the administrator receives the message shown:
No available versions for upgrade
What is causing the current state?

• A.VMware support has expired, so downloads are not available.
• B.vSphere binaries need to be manually uploaded.
• C.The environment is running the latest vSphere version, so no update is required.
• D.The cluster is unable to connect to reIease-api.nutanix-ccm:8

Show Answers

Answer:
Explanation:
ref: https://portal.nutanix.com/page/documents/details?targetId=Web-Console-Guide-Prism-v510:upg-hypervisor-upgrade-esxi-c.html

Question No : 5
An administrator is currently using both 10g uplink with LACP and balance-tcp. A single VM should not be allowed to use more than a single 10G uplink, and both uplinks should be utilized.
Which two command should be used to configure the bond? (choose two)

• A.Ovs-vsctl set port br0-up bond_mode=balance-slb
• B.Ovs-vsctl set port br0-up bond_mode=balance-tcp
• C.Ovs-vsctl set port br0-up bond_mode=active-backup
• D.Ovs-vsctl set port br0-up other_config: bond-rebalance-interval=30000

Show Answers

Answer:

Question No : 6
A consultant is setting up a new vSphere cluster. Customer requirements are as follows:
* VMs should automatically failover to another host if the host crashes
* Host CPU and Memory resources should be evenly balanced
* New VMs should be placed on the host with the most resources available.
Which two settings should be turned on to meet the requirements? (Choose two.)

• A.vShpere DRS
• B.vSphere HA
• C.vSphere vMotion
• D.vSphere Power Management

Show Answers

Answer:

Question No : 7
An administrator is deploying several new application VMs to a Nutanix cluster. The application is very transactional with a 28/72 random, read/write ratio.
What should the administrator do?

• A.Add a minimum of four SSDs to each node toensure all writes go to the SSDs.
• B.Add a minimum of four virtual disks to each VM, and aggregate them on guest OS level.
• C.Add one large SSD to each node and enable Flash Mode for the VMs.
• D.Add one large virtual disk to each V
• E.and use it for all application data.

Show Answers

Answer:
Explanation:
Ref: https://next.nutanix.com/server-virtualization-27/iops-latency-issue-1168

Question No : 8
A customer has Metro Availability configured in Automatic Resume Mode between Site A and Site B What happens to VMs if Primary Site A has full network failure?

• A.Automatic protection domain promotion in Site
• B.VMs automatically restart in Site B
• C.VMs continue to run on Site A following an automatic disable of protection domains.
• D.An administrator must unwitness in Site B and promote protection domains in Site B for VMs to restart
• E.An administrator must promote protection domains in Site B for VMs to restart.

Show Answers

Answer:
Explanation:
Ref: https://support-portal.nutanix.com/page/documents/details/?targetId=Web-Console-Guide-Prism-v55:sto-metro-availability-witness-c.html

Question No : 9
An administrator configures authentication in Prism Central (PC) for the NTNX-Admins group. Users report that they are unable to log in. The administrator confirms that the Active Directory (AD) settings in PC are correct.
Which condition could result in this behavior?

• A.A role mapping needs to be associated with the AD group.
• B.The users must be added to the Domain Admins AD group.
• C.The Local authentication type must also be selected in P
• D.A client chap certificate must also be added in P

Show Answers

Answer:
Explanation:
Ref: https://portal.nutanix.com/page/documents/details?targetId=Prism-Central-Guide-Prism-v5_10:mul-security-role-permissions-pc-t.html

Question No : 10
A consultant finishes creating a new ESXi cluster. The consultant connects to the nodes via laptop and a personal flat switch. The host/CVM network is on VLAN 23. The customer has the native VLAN on the ToR switches set to 23.
The customer wants to use LACP. Before placing the nodes on the customer network, the consultant tags VLAN 23 for each host and CVM. The consultant connects the nodes to the customer network and finds that they are unreachable.
What is causing this issue?

• A.The customer has LACP fallback enabled on switch ports.
• B.The hosts have not been migrated to a vSphere Distributed Switch.
• C.Under the vSwitch0 settings, the consultant did not select Route based on IP hash.
• D.The host and CVM are incorrectly configured.

Show Answers

Answer: