Question No : 1
The connection between DC1 and DC2 is routed as shown in the exhibit.



In this scenario, which statement is correct?

• A.The border devices must be able to perform Layer 3 routing and provide IRB functionality.
• B.L3VPN must be enabled to advertise reachability.
• C.An IP prefix route provides encoding for intra-subnet forwarding.
• D.Type 2 and Type 5 routes will be exchanged between DC1 and DC2.

Show Answers

Answer:

Question No : 2
Referring to the exhibit, which two statements are correct? (Choose two.)

• A.The DS-2 switch will be root bridge for MSTI 2.
• B.The DS-1 switch will be root bridge for MSTI 1.
• C.The DS-1 switch will be root bridge for MSTI 2.
• D.The DS-2 switch will be root bridge for MSTI 1.

Show Answers

Answer:

Question No : 3
You are deploying IP phones in your enterprise networks. When plugged in, the IP phones must be automatically provided with the correct VLAN ID needed for sending voice traffic to the EX Series switches.
In this scenario, which two solutions are required to accomplish this task? (Choose two.)

• A.Enable LLDP-MED on appropriate access interfaces.
• B.Create two VLANs and assign them as VLAN members to the appropriate access interfaces.
• C.Enable the voice VLAN feature with the appropriate access interfaces and VLAN ID for voice traffic.
• D.Use LLDP on appropriate interfaces.

Show Answers

Answer:

Question No : 4
Referring to the exhibit, which two statements are correct? (Choose two.)

• A.The host that the route is associated with is multihomed to two leaf nodes.
• B.The route is a Type 1 EVPN route.
• C.The route is a Type 2 EVPN route.
• D.The host that the route is associated with is single-homed to one leaf node.

Show Answers

Answer:

Question No : 5
You are deploying an 802.1X solution and must determine what would happen if clients are unable to re-authenticate to the RADIUS server.
In this scenario, which configuration would provide access to the network if the supplicant is already authenticated?

• A.move
• B.permit
• C.deny
• D.sustain

Show Answers

Answer:

Question No : 6
You must ensure that all routes in the 10.0.0/8 address range are not advertised outside of your AS.
Which well-known BGP community should be assigned to these addresses to accomplish this task?

• A.no-export
• B.no-peer
• C.internet
• D.no-advertise

Show Answers

Answer:

Question No : 7
Which three configuration parameters must match on all switches within the same MSTP region? (Choose three.)

• A.VLAN to instance mapping
• B.revision level
• C.configuration name
• D.bridge priority
• E.region name

Show Answers

Answer:

Question No : 8
Your network has an unmanaged switch between the hosts and your EX Series switch.
After the traffic enters the EX Series switch, each host must be on a separate VLAN.



How would you accomplish this task?

• A.Configure an input firewall filter on interface ge-0/0/3 to match the source MAC or IP address of the hosts to assign the VLANs.
• B.Configure an output firewall filter on interface ge-0/0/1 to match the destination MAC or IP address of the hosts to assign the VLANs.
• C.Configure interface ge-0/0/3 to a mode trunk to assign the VLANs.
• D.Configure VSTP on interface ge-0/0/1 to assign the VLANs.

Show Answers

Answer:

Question No : 9
Referring to the exhibit, anycast RP is implemented to ensure multicast service availability.



The source is currently sending multicast traffic using group 239.1.1.1 and R3 is receiving PIM register messages, but R2 does not have active source information.
In this scenario, what are two methods to receive the active source information on R2? (Choose two.)

• A.Configure an RP set in PIM on R1, allowing R1 to forward PIM register messages to R2 and R3 in the set.
• B.Configure an MSDP protocol between R2 and R3.
• C.Configure an RP set in PIM on R2 and R3, allowing the RPs to forward PIM register messages to the other RPs in the set.
• D.Configure an MSDP protocol between R1 and R2.

Show Answers

Answer:

Question No : 10
You are deploying new Juniper EX Series switches in a network that currently is using Cisco’s Per-VLAN spanning tree plus (PVST+) and you must provide compatibility with this environment.
Which spanning tree protocol do you deploy in this scenario?

• A.STP
• B.MSTP
• C.VSTP
• D.RSTP

Show Answers

Answer: